
Bitülast BTL 200
ADVANTAGES
•High elasticity and capability of bridging cracks.
•Not affected by microorganisms and aggressive underground waters.
•Forms a flexible, covering and continuous asphalt layer on horizontal and vertical surfaces, dry and slightly moist surfaces.
•No damage to environment as it is water based. Easy to use indoors.
•No separation of swelling by time due to very good adherence.
TECHNICAL SPECIFICATIONS
Basis: Rubber - Bitumen
Color: Brown
Form: viscous liquid
Density: approx. 1,0 kg/lt
Flash Point: No flash
Application Temperature: +5 °C/ +35 °C
Service Temperature: -10 °C / +85°C
Chemical Resistance: resistant against diluted acid, alkali, chlorite and sulfate ions
PLACES OF USE
•As water and moisture tight material from the direction of water flow in underground applications such as foundation, retaining wall and basement,
•As water isolation material in dry or slightly moist details such as kitchen, bathroom, etc.,
•Waterproofing applications resistant to high pressure water, together with polyester felt, isolation fabric, etc.,
•As protective layer on isolation coats or filling of surface pits by mixing with screened fine sand and some cement,
•Insulation of planter boxes,
•Insulation of underground parts of artistic structures against water and moisture.
SURFACE PREPARATION
The application surface should be free of dust, dirt, rust and oil, and loose parts scraped. Pointed tips and sharp corners should be rounded. If required, BTR 100 may be applied without thinned or by thinning Bitülast BTL 200 with water by 1:1 by weight.
APPLICATION
The application surface should be checked for smoothness, dryness and cleanliness and adequate slope grout before applying the primer. After meeting these requirements, is applied on the surface by means of brush or spray gun, as 1.5 kg per sqm on horizontal surfaces and 0.8 kg per sqm on walls, and left until it fully dries. It fully dries in approximately 4-5 hours depending on weather conditions. In case of double-layer applications, the second layer should not be applied until the first layer fully dries. Application of bituminous membrane is started after the primer is completely dry.
CONSUMPTION
1.5 kg per sqm on horizontal surfaces, and 0.8 kg per sqm on walls depending on smoothness of the application surface.
STORAGE CONDITION AND SHELFLIFE
Keep in dry area and protect against direct sunlight. The shelf life is 12 months for a closed product. The date of production takes place on the package.
BTM Bitümlü Tecrit Maddeleri Sanayi ve Ticaret A.Ş. Kemalpaşa O.S.B. Mahallesi Gazi Bulvarı No:152 35730 Kemalpaşa/İzmir TURKEY Phone:+90 232 877 04 02 Fax:+90 232 877 04 10 info@btm.co • www.btm.co
Technical documents
Technıcal Data Sheets
- PDFBitülast BTL 200Request document
Declaratıon of Performance
- PDFDOP11: EN 1504-2 Bitulast BTL200Request document
Qualıty Certıfıcates
- PDFCE Belgesi EN 1504-2 (SZUTEST) - Alfahibrit-Elastodryroof-BitulastRequest document
- PDFTS EN 1504-2 Alfahibrit-Elasto Dryroof- BitülastRequest document
Products in the same group

Bitümento BT2K 500
Brush Applied, Water Based, Flexible, Two Component Waterproofing Material enhanced with Polymers and Reinforcing Fibres Flexible waterproofing material free of solvents and reinforced with fiber as well as polymer, rubb

Bitümento BT2K 600
Bitumento BT2K 600 is a solvent-free, two-component, elastic, water-based, fiber reinforced, rubber and cement based bitumen waterproofing material. More ...

BT2K 600 PLUS
Polymer-modified bitumen-rubber based, two-component, fiber-reinforced, flexible, high-viscosity liquid waterproofing material, applicable by brush or spray machine. More ...

Bitümento BT2K 750
Dual component, flexible, water based, fibre reinforced rubber-polymer modified bitumen waterproofing BT2K 750 waterproofing has been designed for protection of structures against water with carefully chosen rubber-polym