
Elastomast ELM 300
ADVANTAGES
- It has high elasticity and crack bridging properties.
- It is not affected by microorganisms and aggressive underground water.
- It forms a flexible, covering and uninterrupted asphalt layer on horizontal surfaces.
- As it strongly adheres on the area of application, no problem such as flaking and bubbling in encountered in time.
- It reduces the rail vibration, thus reducing the influence of the vibration on surrounding buildings.
TECHNICAL SPECIFICATIONS
- Basis: Bitumen Mastic
- Color: Black
- Form: Paste form after melting
- Heat Resistance: min 120°C
- Cold Resistance: max -25°C
- Density: ~ 1.3 g/cm3
- Application Temperature: 160°C -180°C
PLACES OF USE
- Dampproofing exterior below-grade foundations and walls,
- As water isolation material in dry or slightly moist details such as terrace, kitchen, bathroom, etc.,
- As primer under bituminous coatings,
- As primer material and binder in fiber glass, canvas, etc. applications,
- Anti-corrosive protection for metallic surfaces such as steel construction, pipe, etc.
- As an additive improving tightness and adherence in the mortars and plasters formed by cement and/or fine sand,
- In order to prevent flexion of construction templates due to water and as template separator
SURFACE PREPARATION
The crack to be filled should be cleared from substances preventing adhesion by means of a hard sweeper, wire brush or air compressor, and it should be dry. Depending on the surface of application, BITUSOL or BITUMER should be applied on the surface of application as primer when required, and its complete drying should be ensured.
APPLICATION
Melted in an appropriate melting boiler (melting in a double-wall boiler, the jacked which is filled with heat transferring oil, is preferred) at 160-180 ºC, ELASTOMAST is poured in the joint or crack.If it is used road repave, the material mixture which is obtained by sand and breaking basalt or limestone is scattered on the filling slightly heated by means of a torch.
CONSUMPTION
It varies depending on the smoothness of the surface of application and the thickness of application.
PACKAGING
ELASTOMAST is presented in Net 21 kg tin packages.
STORAGE CONDITION AND SHELFLIFE
It should be stored in covered places.
When stored in its original package unopened in a dry and cool place, its shelf life is 5 years.
WARNINGS
- Gloves and goggles should be used during application.
- The product temperature should not be allowed to exceed 180 oC during the melting process.
- The vapor released by the molten product should not be directly inhaled.
RESPONSIBILITY
The data contained in this technical document is based on scientific knowledge. BTM A.Ş is only responsible for the product quality.
BTM A.Ş. may not be held responsible for other than recommendations on how and where to use the product and/or any improper use and consequences thereof
BTM Bitümlü Tecrit Maddeleri Sanayi ve Ticaret A.Ş. Kemalpaşa O.S.B. Mahallesi Gazi Bulvarı No:152 35730 Kemalpaşa/İzmir TURKEY Phone:+90 232 877 04 02 Fax:+90 232 877 04 10 info@btm.co • www.btm.co
Technical documents
Technıcal Data Sheets
- PDFElastomast ELM 300Request document
Declaratıon of Performance
- PDFDOP1:TS EN 14188-1 ELM 300PDF ↓
Products in the same group

Bitümento BT2K 500
Brush Applied, Water Based, Flexible, Two Component Waterproofing Material enhanced with Polymers and Reinforcing Fibres Flexible waterproofing material free of solvents and reinforced with fiber as well as polymer, rubb

Bitümento BT2K 600
Bitumento BT2K 600 is a solvent-free, two-component, elastic, water-based, fiber reinforced, rubber and cement based bitumen waterproofing material. More ...

BT2K 600 PLUS
Polymer-modified bitumen-rubber based, two-component, fiber-reinforced, flexible, high-viscosity liquid waterproofing material, applicable by brush or spray machine. More ...

Bitümento BT2K 750
Dual component, flexible, water based, fibre reinforced rubber-polymer modified bitumen waterproofing BT2K 750 waterproofing has been designed for protection of structures against water with carefully chosen rubber-polym